Products

Choose the right product for your boat

Choose a category and browse products for hull protection, maintenance and renewal.

101
products: 10
categories: 3
brands

Delivery across Europe
Secure checkout and genuine products
Free expert advice

Paint additives

15 products

SEAJET THINNER A

SEAJET Thinner A – thinner for antifoulings and primers Genuine xylene-based SEAJET thinner – for the right coating consistency and tool cleaning SEAJET Thinner A is a xylene-based thinner for thinning SEAJET antifoulings, SEAJET 015 Underwater Primer and other SEAJET products where it is specified. Use it to adjust the consistency (viscosity) of the coating for a smooth, even finish, especially at low temperatures or when spraying. It is also suitable for cleaning brushes, rollers and spray equipment. Using the genuine thinner ensures that the coating retains all the properties intended by the manufacturer – an unsuitable thinner can impair drying, adhesion and performance. Which products is it for? All SEAJET antifoulings (021, 027, 030, 031, 032, 033, 034, 036, 037, 038, 039, 040) SEAJET 015 Underwater Primer SEAJET SEOSIL and SEAJET Tie Coat SEAJET Pellerclean Clear Coat Cleaning tools after using the products listed above Not for two-component epoxy and polyurethane coatings – use SEAJET Thinner E for SEAJET 117, and SEAJET Thinner P for SEAJET 132 and 2300. Advantages Genuine SEAJET thinner – fully compatible with the coatings Smooth, even finish with no brush marks Suitable for spraying and for application at lower temperatures For tool cleaning Technical data Base: xylene Pack sizes: 1 l / 5 l / 20 l Flash point: 25 °C VOC content: 870 g/l Directions for use Add the thinner gradually, stirring the coating well in between. For brush or roller application, as a rule do not add more than 5 % thinner (check the technical data sheet of the individual coating – some, e.g. SEAJET Tie Coat, call for more). For tool cleaning, use the thinner immediately after finishing the job. Tip Too much thinner reduces the film thickness and with it the protection the coating provides. Use only in a well-ventilated area, away from sources of ignition. Close containers tightly after use. Safety labelling (GHS/CLP) Pictograms: GHS02, GHS07, GHS08 Signal word: DANGER H226 Flammable liquid and vapour. H304 May be fatal if swallowed and enters airways. H312 Harmful in contact with skin. H315 Causes skin irritation. H319 Causes serious eye irritation. H332 Harmful if inhaled. H335 May cause respiratory irritation. H373 May cause damage to organs through prolonged or repeated exposure.

from€13.34

SEAJET THINNER E

SEAJET Thinner E – thinner and cleaner for epoxy coatings Genuine SEAJET thinner for all epoxy primers – for the right consistency, degreasing and tool cleaning SEAJET Thinner E is a xylene-based thinner and cleaner developed specifically for SEAJET epoxy coatings. Use it to adjust the consistency (viscosity) of two-component epoxy primers for a smooth, even application. It is also suitable for cleaning and degreasing the surface before painting, and for cleaning brushes, rollers and spray equipment after the job. Using the genuine thinner ensures that the epoxy coating cures properly and retains all of its protective properties. Which products is it for? SEAJET 117 Multipurpose Epoxy Primer SEAJET 017 Epoxy Bonding Primer for Alloys SEAJET 118 Ultra-Build Epoxy Primer All other SEAJET epoxy coatings Not for antifoulings or one-component coatings – use SEAJET Thinner A for those; for polyurethane coatings (SEAJET 132, 2300) use SEAJET Thinner P. Advantages Genuine SEAJET thinner – fully compatible with epoxy coatings Smooth, even application For degreasing the surface before applying the primer For cleaning tools after working with epoxy coatings Technical data Base: xylene Pack sizes: 1 l / 5 l / 20 l Flash point: 13 °C (highly flammable) VOC content: 850 g/l Directions for use Thinning: add the thinner only after the base and hardener have been mixed. Add it gradually and stir well. Do not add more than 5 %. Degreasing: before painting, wipe the surface with a clean cloth moistened with thinner and allow the solvent to evaporate completely. Tool cleaning: clean tools immediately after use, before the epoxy starts to cure. Tip Too much thinner reduces the film thickness and can impair protection against osmosis and corrosion. Because of the low flash point, use only in a well-ventilated area, away from sources of ignition, sparks and open flames. Safety labelling (GHS/CLP) Pictograms: GHS02, GHS07, GHS08 Signal word: DANGER H225 Highly flammable liquid and vapour. H304 May be fatal if swallowed and enters airways. H312 Harmful in contact with skin. H315 Causes skin irritation. H319 Causes serious eye irritation. H335 May cause respiratory irritation. H336 May cause drowsiness or dizziness. H373 May cause damage to organs through prolonged or repeated exposure.

from€13.47

SEAJET THINNER P

SEAJET Thinner P – thinner for polyurethane coatings Original SEAJET thinner for two-component polyurethane paints and varnishes – for a mirror-like gloss with no brush marks SEAJET Thinner P is a thinner for polyurethane coatings, developed specifically for SEAJET two-component polyurethane products. Use it to adjust the consistency (viscosity) of the paint or varnish so that it flows out and levels nicely during application – giving you a smooth, high-gloss finish with no brush or roller marks. It is also suitable for cleaning tools after working with polyurethane coatings. Polyurethane coatings are sensitive to unsuitable thinners, which can cause cloudiness, poor curing or loss of gloss – so always use the original thinner. Which products is it for? SEAJET 132 Polyurethane Topcoat – add 15–25 % SEAJET 130 Polyurethane Gloss Varnish – add a maximum of 10 % SEAJET 2300 Hard Coating – add 0–5 % Not for antifoulings or epoxy coatings – for antifoulings use SEAJET Thinner A, and for epoxy coatings (SEAJET 117) use SEAJET Thinner E. Advantages Original SEAJET thinner – full compatibility with polyurethane coatings Excellent flow – smooth, mirror-like finish with no tool marks Preserves the gloss and hardness of the polyurethane coating For cleaning tools Instructions for use Add the thinner only after mixing the base and hardener. Add gradually and stir well. Observe the recommended amount for each product (see above). Clean tools immediately after use, before the coating starts to cure. Tip At higher temperatures add slightly more thinner so that the coating flows out properly; at lower temperatures add less. Use only in a well-ventilated area, away from sources of ignition, sparks and open flames. Close the container tightly after use – the thinner must not come into contact with moisture. Technical data Type: thinner for polyurethane coatings Pack sizes: 1 l / 5 l Shelf life: at least 3 years at 20 °C Safety labelling (GHS/CLP) Hazard pictograms are shown on the product page; read the label and safety data sheet before use.

from€17.75

SEAJET THINNER U

SEAJET Thinner U – thinner for alkyd paints, varnishes and primers Original SEAJET thinner for one-component paints and varnishes above the waterline – for smooth application and cleaning tools SEAJET Thinner U is an alkyd thinner for thinning SEAJET one-component paints, varnishes and primers for use above the waterline. It lets you adjust the consistency (viscosity) of the coating so that it flows out and levels nicely – giving you a smooth, glossy finish with no brush marks. It is also suitable for cleaning brushes, rollers and spray equipment, and for degreasing and cleaning gelcoat before painting. Which products is it for? SEAJET 012 Universal Primer/Undercoat SEAJET 120 UV Varnish – for varnish, also for thinning the first coats (1st coat up to 50%, 2nd coat up to 25%, subsequent coats up to 10%) SEAJET 122 Brilliance Most other alkyd paints and varnishes Not for antifoulings, epoxy or polyurethane coatings – for these, use SEAJET Thinner A (antifoulings), Thinner E (epoxies) or Thinner P (polyurethanes). Benefits Original SEAJET thinner – full compatibility with SEAJET paints and varnishes Excellent flow – smooth, glossy finish Suitable for spraying and brushing For degreasing gelcoat before painting For cleaning tools Technical data Type: alkyd thinner (petroleum-based odour) Pack sizes: 1 l / 5 l Flash point: 40 °C VOC content: 781 g/l Shelf life: at least 3 years at 20 °C Directions for use Thinning: add the thinner gradually, stirring the coating well in between. Follow the recommended quantity in the technical data sheet of the respective coating. Degreasing: wipe the surface with a clean cloth moistened with thinner and allow the solvent to evaporate completely. Cleaning tools: clean tools immediately after work. Tip Too much thinner reduces the film thickness and the hiding power of the paint. Use only in a well-ventilated area, away from sources of ignition. Close the container tightly after use. Safety labelling (GHS/CLP) Pictograms: GHS02, GHS08 Signal word: DANGER H226 Flammable liquid and vapour. H304 May be fatal if swallowed and enters airways. EUH066 Repeated exposure may cause skin dryness or cracking.

from€15.00

International THINNER N.3

€22.00

International NON-SLIP ADDITIVE

€12.00

International THINNER 910 1 LT FAST SPRAY SOLVENT

€36.00

International Thinner GTA220

This item is intended for B2B sale. International Thinner GTA220 is a dedicated thinner and equipment cleaner for International epoxy coating systems such as Intergard 7500, Intergard 7600, Intershield 300 and Intergard 263. GTA220 is mainly used for cleaning spray equipment, brushes and rollers during and after the application of epoxy coatings. Where the product's technical data sheet explicitly allows it, it can also be added to improve workability in more demanding application conditions. It is used exclusively as a complement to an epoxy coating system – it is not intended for thinning polyurethane (PU), silicone or fluoropolymer coatings. For these, use International Thinner GTA713 or the dedicated GTA007 for antifouling coatings. KEY FEATURES Dedicated thinner for International epoxy coating systems Effective cleaning of spray equipment, brushes and rollers Compatible with Intergard 7500, Intergard 7600, Intershield 300 and Intergard 263 Clear, colourless product For professional use AREAS OF USE Use GTA220 only in combination with International epoxy products for which it is explicitly specified in the technical data sheet as the appropriate thinner or cleaner. Cleaning spray equipment after applying epoxy coatings (primers and intermediate coats) Thinning epoxy coatings in more demanding application conditions, in compliance with local volatile organic compound (VOC) regulations Keeping tools clean during breaks in work APPLICATION Under normal application conditions, thinning is not required. If the technical data sheet of the specific product permits thinning, add a maximum of 5 % GTA220. For cleaning, rinse all equipment thoroughly immediately after use, before the coating dries. Do not mix GTA220 with materials that are not part of the epoxy coating system (e.g. polyurethane or silicone products). COMPATIBILITY GTA220 is the specified thinner and cleaner for the epoxy products Intergard 7500, Intergard 7600, Intershield 300 and Intergard 263. For polyurethane (Interthane) coatings, use International Thinner GTA713. IMPORTANT GTA220 is a flammable liquid intended for professional use only. Follow all safety instructions in the product safety data sheet (SDS) when working with it. The information in this description is not exhaustive. Always check the current technical and safety data sheets before use.

€187.00

International Thinner GTA713

€49.99

International THINNER N. 100 1

€37.16

International THINNER N.1 1 LT

€22.00

International THINNER N.7 1 LT

€22.00

International THINNER N.9 1 LT

€27.00

International VC GENERAL THINNER 1l

€33.00

JUST TEAK (STEP 2/BRIGHTENER)

from€27.45

Loading products…

How to choose

Not sure which product?

1
Determine the boat type
Sailing yacht, motor yacht or speedboat — each type asks something different of the coating.
2
Choose the sailing area
Warm Mediterranean, cooler Adriatic or a lake — the conditions decide the type of antifouling.
3
Pick the system
Ablative, hard or copper-free — primer, antifouling and the extras that belong together.

Browse the coating systems

Why Choose Us?

Advantages that set us apart from others.

Choosing an antifouling contractor is an important decision, as it involves protecting your vessel, which represents a significant investment. Here are some reasons why many boat and yacht owners trust us:

More about us

Experience and Expertise
We take care of the protection and maintenance of various vessels, from smaller boats to yachts. We are well acquainted with the procedures and materials, so we guarantee safe and effective protection.
Quality Materials
We only use proven antifouling coatings from reputable manufacturers. This ensures long-lasting hull protection, lower fuel consumption, and better vessel gliding.
Individual Approach
Each vessel is different, so we always carry out an inspection before application and adapt the protection to your needs, boat type, and conditions of use.
Reliability
We adhere to agreed deadlines and perform the work accurately. Our priority is to prepare your boat for the new season in a timely and flawless manner.

Contact

Not sure what to choose?

Our team will advise you, present the protection options, and together we will find the best solution for your vessel.

Call +386 (0)51 855 299 Send an inquiry

info@antifouling.si

Grab the helm and give it a spin

0
turns: 0
top speed (rpm)

International Thinner GTA220

€187.00

Products

Paint additives

Not sure which product?

Determine the boat type

Choose the sailing area

Pick the system

Advantages that set us apart from others.

Experience and Expertise

Quality Materials

Individual Approach

Reliability

Not sure what to choose?

Paint additives