International Intersleek 1100SR

Name: International Intersleek 1100SR
Brand: international
SKU: international-intersleek-1100sr
Price: 1860.00 EUR

€1860.00

Select packaging below to see the exact price.

Colour

Available packaging

Select packaging …

Secure paymentFast delivery across Europe

Part of a coating system

System B – Foul Release (biocide-free)·3. Fluoropolymer topcoat
1. Primer2. Silicone tie coat3. Fluoropolymer topcoat
Apply first: Primer → Silicone tie coat

See the whole system

Hazard pictograms

Read the label and safety data sheet before use.

Description

This item is intended for B2B sale. International Intersleek 1100SR (black) is an advanced three-component fluoropolymer foul-release coating for controlling slime fouling on the underwater hull of a vessel. Intersleek 1100SR creates an ultra-smooth, glossy surface to which organisms cannot firmly attach. This significantly reduces fouling build-up and maintains the hull's hydrodynamic efficiency throughout the entire service interval. It is a biocide-free system – it contains no active antifouling substances and works purely on the basis of a low-energy surface (foul-release technology). **KEY FEATURES** - Three-component (3K) advanced fluoropolymer foul-release coating - Biocide-free – works purely on the basis of a low-energy, smooth surface - Slime control - No induction time required after mixing - Suitable for newbuilds and maintenance work - Glossy finish; colour: black (the product is also available in grey, blue and red) **AREAS OF USE** Intersleek 1100SR is applied exclusively over a previously applied Intersleek tie coat, within the specified overcoating interval, on the underwater hull of the vessel. - Underwater hulls of vessels where biocide-free fouling control is the priority - Newbuilds and major refits with biocide-free systems - Vessels where long-term hydrodynamic hull efficiency is important **APPLICATION** - Intersleek 1100SR must be applied over an Intersleek tie coat (e.g. Intersleek 737) within the specified overcoating interval. - The recommended application method is airless spray; brush and roller are used only for small areas and touch-ups. - All equipment must be thoroughly cleaned before use, as traces of other materials can affect the quality and appearance of the finish. - Thinner/cleaner: International GTA007 or GTA822. - For surface preparation, application temperatures and overcoating intervals, always follow the current International technical data sheet (TDS). **COMPATIBILITY** Intersleek 1100SR is the finish coat of a biocide-free foul-release system and is applied exclusively over an Intersleek tie coat on top of a suitable epoxy primer (e.g. Intershield 300, Intergard 7500 or Intergard 7600). The system is not interchangeable with conventional antifouling systems (e.g. Interspeed, Interswift) – these are two separate fouling protection technologies. **IMPORTANT** Intersleek 1100SR is a professional three-component fluoropolymer coating. All three components form a single system and must be used in the specified mixing ratio of 9 : 2 : 1 (by volume). Technical data may vary depending on the colour shade, area of use and application conditions. Always check the current technical and safety data sheets before use.

Similar products

Intergard 7500

This item is intended for B2B sales. International Intergard 7500 aluminium is a high-performance, two-component pure epoxy universal primer with high volume solids (80 %), pigmented with aluminium, providing excellent long-term corrosion protection for steel surfaces. It is designed for professional protection in demanding marine environments. Thanks to advanced rheology technology, it offers improved airless spray application with lower thinner consumption and excellent edge retention. It is suitable for fast curing and application at low temperatures, down to –15 °C. Intergard 7500 is used as a universal epoxy primer on various areas of a vessel – from the underwater hull to water ballast tanks – in professional coating systems for newbuilding or maintenance. KEY FEATURES two-component pure epoxy coating with high volume solids (80 %) aluminium pigment for additional mechanical and corrosion resistance excellent long-term corrosion protection advanced rheology technology for easier spraying and lower thinner consumption excellent edge retention fast curing, can be applied at low temperatures, down to –15 °C suitable for the underwater hull, decks, superstructure and ballast tanks AREAS OF USE Intergard 7500 aluminium is intended for the professional protection of steel surfaces where effective, long-lasting corrosion protection and good resistance to mechanical stress are required. underwater hull of the vessel decks and steel structures exterior superstructure water ballast tanks mechanically prepared surfaces with shop primer APPLICATION Before application, surfaces must be properly prepared, clean and free of contaminants, abrasive blasted to Sa 2½ (ISO 8501-1:2007) or SSPC-SP10. The recommended application method is airless spray with a 0.63–0.79 mm tip at a pressure of at least 211 kg/cm². Small areas can be coated by brush or roller (several coats may be required). For thinning, use only International GTA220 (max. 5 %). For cleaning equipment, use International GTA822 or GTA220. For surface preparation, choice of equipment, application temperatures, drying times and overcoating intervals, always follow the current International Technical Data Sheet (TDS). COMPATIBILITY Intergard 7500 is used as a primer in System A (together with Intergard 263 and Interspeed 6400 / Interswift 6800HS) or in System B (together with Intersleek 737 and Intersleek 1100SR). As a subsequent coat over Intergard 7500, the manufacturer's official system recommends Intergard 7500 (an additional coat) or Interthane 990. Alternatives to this product in the primer role are Intershield 300 ENA aluminium (higher abrasion resistance) and Intergard 7600 (a more economical choice for less demanding applications). IMPORTANT Intergard 7500 is a professional two-component epoxy coating. Part A and Part B form a single system and must be used in the specified mixing ratio of 3 : 1. Technical data may vary depending on colour shade, area of use, coating system and application conditions. Always check the current technical and safety data sheets before use.

€448.75

International Intergard 263

This item is intended for B2B sales. International Intergard 263 is a two-component tar-free epoxy tie coat designed to link an anticorrosive primer with an antifouling or cosmetic topcoat. Intergard 263 ensures maximum adhesion and long-term performance of the coating system on exterior hull areas, both above and below the waterline. It can also be used as a sealer coat over old TBT antifoulings, as at the specified thickness of 100 μm it forms a certified barrier against TBT leaching (tested to ASTM D5108-96, modified). Intergard 263 is a versatile product suitable for a wide range of new and aged coating systems, whether for newbuilding, major refits or routine on board maintenance. KEY FEATURES two-component tar-free epoxy tie coat maximum adhesion between primer and topcoat compatible with a wide range of antifouling and cosmetic topcoats certified as a barrier against TBT leaching over old TBT antifoulings suitable for topside and underwater hull areas suitable for newbuilding, major refits and on board maintenance good resistance to chalking and discolouration. AREAS OF USE Intergard 263 is always applied over a previously applied and properly prepared epoxy anticorrosive primer (e.g. Intershield 300, Intergard 7500 or Intergard 7600) within the specified overcoating interval. exterior hull (above and below the waterline) before application of antifouling as an intermediate coat before cosmetic (coloured) topcoats as a sealer coat over existing TBT antifoulings newbuilding, major refits or on board maintenance. APPLICATION The substrate (primer) must be dry and free of contamination (oil, grease, salt) and must be overcoated with Intergard 263 within the specified overcoating interval – see the technical data sheet of the relevant primer. The recommended application method is airless spray with a 0.46–0.66 mm tip at a pressure of at least 176 kg/cm² (2500 psi). Brush or roller should only be used for small areas or touch-ups, where several coats may be required. Thinning is usually not required; in exceptional cases use only International GTA220. Use GTA822 or GTA220 for equipment cleaning. For surface preparation, application temperatures and overcoating intervals, always follow the current International Technical Data Sheet (TDS). COMPATIBILITY Intergard 263 is the intermediate link in System A: it is applied over Intershield 300 / Intergard 7500 / Intergard 7600 and then overcoated with Interspeed 6400 or Interswift 6800HS. For the silicone/fluoropolymer system (Intersleek 737 + Intersleek 1100SR), the dedicated silicone tie coat Intersleek 737 is used instead of Intergard 263. IMPORTANT Intergard 263 is a professional two-component epoxy coating. Part A and Part B form a single system and must be used in the specified mixing ratio of 4 : 1. Technical data may vary depending on colour, area of use, coating system and application conditions. Always check the current technical and safety data sheets before use.

€373.75

International Interswift 6800 HS Black

This item is intended for B2B sales. International Interswift 6800HS black is a one-component, organotin-free (TBT-free), self-polishing (SPC – Self Polishing Copolymer) low-friction antifouling based on patented copper acrylate technology. Thanks to its controlled polishing action, Interswift 6800HS maintains a smooth, hydrodynamic surface throughout the entire in-service period (the surface is 12% smoother than a typical CDP antifouling), reducing hull drag and fuel consumption. A high volume solids content (62%) allows faster application with less waste. Interswift 6800HS is suitable for newbuilding and maintenance work on deep-sea and coastal commercial vessels, with an in-service period of up to 60 months. KEY FEATURES one-component (1K) antifouling, no mixing with a hardener required organotin-free (TBT-free), patented copper acrylate (SPC) technology low friction and a smooth surface (12% smoother than CDP) for reduced hull drag and lower fuel consumption high volume solids (62%) for less waste during application in-service period of up to 60 months suitable for application over existing antifoulings in good condition approved by leading classification societies (Lloyd's Register, DNV GL, Bureau Veritas, Korean Register of Shipping) AREAS OF USE Interswift 6800HS is applied exclusively to a previously prepared and coated substrate on the underwater hull of the vessel, and is suitable for both newbuilding and refurbishment work. underwater hulls of deep-sea and coastal commercial vessels newbuilding and major overhauls renewal of an existing antifouling in good condition vessels where long-term hydrodynamic hull efficiency is important APPLICATION Before application, the substrate (primer/intermediate coat) must be clean, dry and within the specified overcoating interval for the undercoat – see the primer's technical data sheet. When applying over an existing antifouling layer, the area must be thoroughly cleaned by high-pressure fresh water washing (3000 psi, 211 kg/cm²). Before use, stir the material thoroughly with a mechanical stirrer (some colours require additional mixing). Thinning is not recommended; use International GTA007 to clean equipment. The recommended application method is airless spray. Brush or roller application is possible for smaller areas. COMPATIBILITY Interswift 6800HS is the finish (antifouling) coat of System A, applied over Intergard 263 (intermediate coat) on top of Intershield 300 / Intergard 7500 / Intergard 7600 (primer). For a shorter in-service period and a lower purchase price, Interspeed 6400 (up to 36 months) is also available within the same system. IMPORTANT Interswift 6800HS is a professional antifouling for professional use. Once immersed, some colours may change shade (e.g. red → light red, brown → dark brown/black) – this does not affect the performance of the coating. Technical data may vary depending on colour, area of use and application conditions. Always check the current technical and safety data sheet of the product before use.

€950.00

International Interspeed 6400 TBT-free CDP Controlled Depletion Polymer

This item is intended for B2B sales. International Interspeed 6400 black is a one-component, organotin-free (TBT-free), self-polishing (CDP – Controlled Depletion Polymer) antifouling for long-term protection of the underwater hull against fouling. Interspeed 6400 provides controlled, even biocide release throughout the entire service interval, ensuring predictable performance and easy drydock planning. Its high solids content (60%) reduces paint waste and improves workability. It is suitable for both newbuilding and maintenance work, and for refurbishment it can, under certain conditions, be applied directly over an existing antifouling in good condition. It is an economical and reliable solution for commercial vessels and yachts operating in temperate or tropical waters, with a service interval of up to approximately 36 months. KEY FEATURES one-component (1K) antifouling, no hardener mixing required organotin-free (TBT-free), compliant with the IMO AFS 2001 convention self-polishing (CDP) technology for controlled biocide release high volume solids (60%) for less waste during application service interval of up to approximately 36 months suitable for newbuilding and maintenance work under certain conditions, can be applied directly over an existing antifouling in good condition AREAS OF USE Interspeed 6400 is applied exclusively over a properly prepared and coated substrate (a suitable intermediate or primer system) on the underwater hull. underwater hulls of commercial vessels and yachts newbuilding and major refits renewal of existing antifouling (in accordance with the surface preparation instructions) vessels in temperate and tropical waters, for deep-sea and coastal trading APPLICATION Before application, the substrate (primer/intermediate coat) must be clean, dry and within the specified overcoating interval for the base coat – see the primer's technical data sheet. When applying over an existing antifouling, the leached layer must first be removed by high-pressure fresh water washing (3000 psi, 211 kg/cm²). Stir the material thoroughly with a mechanical stirrer before use. Thinning is not recommended; in exceptional circumstances use only the dedicated International GTA007 thinner (not included in this price list – consult technical support before use). The recommended application method is airless spray. Brush or roller may be used for smaller areas. Observe the specified maximum exposure times before launching – up to 6 months in temperate conditions and up to 3 months in tropical conditions. COMPATIBILITY Interspeed 6400 is the finish (antifouling) coat of System A, applied over Intergard 263 (intermediate coat) on top of Intershield 300 / Intergard 7500 / Intergard 7600 (primer). For a longer-term solution (up to 60 months), Interswift 6800HS is also available in the same system. IMPORTANT Interspeed 6400 is a professional antifouling for professional use. The colour may change on immersion in water – this does not affect the coating's performance. Technical data may vary depending on colour, area of use and application conditions. Always check the current technical and safety data sheets before use.

€698.88

Contact

Not sure what to choose?

Our team will advise you, present the protection options, and together we will find the best solution for your vessel.

Call +386 (0)51 855 299 Send an inquiry

info@antifouling.si

Grab the helm and give it a spin

0
turns: 0
top speed (rpm)