International Intergard 263

Name: International Intergard 263
Brand: international
SKU: international-intergard-263
Price: 373.75 EUR

This item is intended for B2B sales. International Intergard 263 is a two-component tar-free epoxy tie coat designed to link an anticorrosive primer with an antifouling or cosmetic topcoat.

€373.75

Select packaging below to see the exact price.

Available packaging

Select packaging …

Secure paymentFast delivery across Europe

Part of a coating system

System A – antifouling·2. Tie coat
1. Primer2. Tie coat3. Topcoat
Apply first: Primer

See the whole system

Hazard pictograms

Read the label and safety data sheet before use.

Description

This item is intended for B2B sales. International Intergard 263 is a two-component tar-free epoxy tie coat designed to link an anticorrosive primer with an antifouling or cosmetic topcoat. Intergard 263 ensures maximum adhesion and long-term performance of the coating system on exterior hull areas, both above and below the waterline. It can also be used as a sealer coat over old TBT antifoulings, as at the specified thickness of 100 μm it forms a certified barrier against TBT leaching (tested to ASTM D5108-96, modified). Intergard 263 is a versatile product suitable for a wide range of new and aged coating systems, whether for newbuilding, major refits or routine on board maintenance. KEY FEATURES two-component tar-free epoxy tie coat maximum adhesion between primer and topcoat compatible with a wide range of antifouling and cosmetic topcoats certified as a barrier against TBT leaching over old TBT antifoulings suitable for topside and underwater hull areas suitable for newbuilding, major refits and on board maintenance good resistance to chalking and discolouration. AREAS OF USE Intergard 263 is always applied over a previously applied and properly prepared epoxy anticorrosive primer (e.g. Intershield 300, Intergard 7500 or Intergard 7600) within the specified overcoating interval. exterior hull (above and below the waterline) before application of antifouling as an intermediate coat before cosmetic (coloured) topcoats as a sealer coat over existing TBT antifoulings newbuilding, major refits or on board maintenance. APPLICATION The substrate (primer) must be dry and free of contamination (oil, grease, salt) and must be overcoated with Intergard 263 within the specified overcoating interval – see the technical data sheet of the relevant primer. The recommended application method is airless spray with a 0.46–0.66 mm tip at a pressure of at least 176 kg/cm² (2500 psi). Brush or roller should only be used for small areas or touch-ups, where several coats may be required. Thinning is usually not required; in exceptional cases use only International GTA220. Use GTA822 or GTA220 for equipment cleaning. For surface preparation, application temperatures and overcoating intervals, always follow the current International Technical Data Sheet (TDS). COMPATIBILITY Intergard 263 is the intermediate link in System A: it is applied over Intershield 300 / Intergard 7500 / Intergard 7600 and then overcoated with Interspeed 6400 or Interswift 6800HS. For the silicone/fluoropolymer system (Intersleek 737 + Intersleek 1100SR), the dedicated silicone tie coat Intersleek 737 is used instead of Intergard 263. IMPORTANT Intergard 263 is a professional two-component epoxy coating. Part A and Part B form a single system and must be used in the specified mixing ratio of 4 : 1. Technical data may vary depending on colour, area of use, coating system and application conditions. Always check the current technical and safety data sheets before use.

Similar products

Intergard 7500

This item is intended for B2B sales. International Intergard 7500 aluminium is a high-performance, two-component pure epoxy universal primer with high volume solids (80 %), pigmented with aluminium, providing excellent long-term corrosion protection for steel surfaces. It is designed for professional protection in demanding marine environments. Thanks to advanced rheology technology, it offers improved airless spray application with lower thinner consumption and excellent edge retention. It is suitable for fast curing and application at low temperatures, down to –15 °C. Intergard 7500 is used as a universal epoxy primer on various areas of a vessel – from the underwater hull to water ballast tanks – in professional coating systems for newbuilding or maintenance. KEY FEATURES two-component pure epoxy coating with high volume solids (80 %) aluminium pigment for additional mechanical and corrosion resistance excellent long-term corrosion protection advanced rheology technology for easier spraying and lower thinner consumption excellent edge retention fast curing, can be applied at low temperatures, down to –15 °C suitable for the underwater hull, decks, superstructure and ballast tanks AREAS OF USE Intergard 7500 aluminium is intended for the professional protection of steel surfaces where effective, long-lasting corrosion protection and good resistance to mechanical stress are required. underwater hull of the vessel decks and steel structures exterior superstructure water ballast tanks mechanically prepared surfaces with shop primer APPLICATION Before application, surfaces must be properly prepared, clean and free of contaminants, abrasive blasted to Sa 2½ (ISO 8501-1:2007) or SSPC-SP10. The recommended application method is airless spray with a 0.63–0.79 mm tip at a pressure of at least 211 kg/cm². Small areas can be coated by brush or roller (several coats may be required). For thinning, use only International GTA220 (max. 5 %). For cleaning equipment, use International GTA822 or GTA220. For surface preparation, choice of equipment, application temperatures, drying times and overcoating intervals, always follow the current International Technical Data Sheet (TDS). COMPATIBILITY Intergard 7500 is used as a primer in System A (together with Intergard 263 and Interspeed 6400 / Interswift 6800HS) or in System B (together with Intersleek 737 and Intersleek 1100SR). As a subsequent coat over Intergard 7500, the manufacturer's official system recommends Intergard 7500 (an additional coat) or Interthane 990. Alternatives to this product in the primer role are Intershield 300 ENA aluminium (higher abrasion resistance) and Intergard 7600 (a more economical choice for less demanding applications). IMPORTANT Intergard 7500 is a professional two-component epoxy coating. Part A and Part B form a single system and must be used in the specified mixing ratio of 3 : 1. Technical data may vary depending on colour shade, area of use, coating system and application conditions. Always check the current technical and safety data sheets before use.

€448.75

International Thinner GTA713

€49.99

International Intersleek 1100SR

This item is intended for B2B sale. International Intersleek 1100SR (black) is an advanced three-component fluoropolymer foul-release coating for controlling slime fouling on the underwater hull of a vessel. Intersleek 1100SR creates an ultra-smooth, glossy surface to which organisms cannot firmly attach. This significantly reduces fouling build-up and maintains the hull's hydrodynamic efficiency throughout the entire service interval. It is a biocide-free system – it contains no active antifouling substances and works purely on the basis of a low-energy surface (foul-release technology). KEY FEATURES Three-component (3K) advanced fluoropolymer foul-release coating Biocide-free – works purely on the basis of a low-energy, smooth surface Slime control No induction time required after mixing Suitable for newbuilds and maintenance work Glossy finish; colour: black (the product is also available in grey, blue and red) AREAS OF USE Intersleek 1100SR is applied exclusively over a previously applied Intersleek tie coat, within the specified overcoating interval, on the underwater hull of the vessel. Underwater hulls of vessels where biocide-free fouling control is the priority Newbuilds and major refits with biocide-free systems Vessels where long-term hydrodynamic hull efficiency is important APPLICATION Intersleek 1100SR must be applied over an Intersleek tie coat (e.g. Intersleek 737) within the specified overcoating interval. The recommended application method is airless spray; brush and roller are used only for small areas and touch-ups. All equipment must be thoroughly cleaned before use, as traces of other materials can affect the quality and appearance of the finish. Thinner/cleaner: International GTA007 or GTA822. For surface preparation, application temperatures and overcoating intervals, always follow the current International technical data sheet (TDS). COMPATIBILITY Intersleek 1100SR is the finish coat of a biocide-free foul-release system and is applied exclusively over an Intersleek tie coat on top of a suitable epoxy primer (e.g. Intershield 300, Intergard 7500 or Intergard 7600). The system is not interchangeable with conventional antifouling systems (e.g. Interspeed, Interswift) – these are two separate fouling protection technologies. IMPORTANT Intersleek 1100SR is a professional three-component fluoropolymer coating. All three components form a single system and must be used in the specified mixing ratio of 9 : 2 : 1 (by volume). Technical data may vary depending on the colour shade, area of use and application conditions. Always check the current technical and safety data sheets before use.

€1860.00

International Intershield 300

This item is intended for B2B sales. International Intershield 300 is a premium two-component, abrasion-resistant epoxy universal primer with aluminium pigment, and the industry standard for the most demanding long-term corrosion protection of steel surfaces. Formulated on proprietary polymer technology, it allows fast curing and overcoating even at low temperatures. It stands out for its exceptional resistance to mechanical damage (abrasion), which reduces the risk of subsequent corrosion from impacts, scratches and wear. Its aluminium pigment (up to 10 % of dry film weight) provides an additional barrier against the spread of corrosion on steel and improved resistance to cathodic disbondment. Intershield 300 is used as a universal primer on all areas of the vessel – underwater hull, decks, superstructure and tanks – for both newbuilding and maintenance work, with more than 30 years of proven performance in the industry. KEY FEATURES two-component pure epoxy coating with aluminium pigment exceptional abrasion resistance and long-term corrosion protection industry standard with more than 30 years of proven performance fast curing, can be applied at low temperatures down to –15 °C (down to –20 °C in certain locations) suitable for use with cathodic protection suitable for potable water tanks (BS6920:2000 certification) suitable for newbuilding and maintenance work suitable for demanding marine and offshore environments AREAS OF USE Intershield 300 is designed for the most demanding professional protection of steel surfaces, where high resistance to mechanical damage matters as much as corrosion protection. underwater hull exterior superstructure and decks offshore structures and platforms water ballast tanks, storage tanks and potable water tanks mechanically prepared shop-primed surfaces or bare steel APPLICATION Before application, surfaces must be properly prepared, clean, dry and free of contaminants, abrasive blasted to Sa 2½ (ISO 8501-1:2007) or at least Sa2/SSPC-SP6 (for non-immersed surfaces). The recommended application method is airless spray with a 0.66–0.79 mm tip at a pressure of at least 211 kg/cm² (3000 psi). Smaller areas can be coated by brush or roller (several coats may be required). Use only International GTA220 for thinning and equipment cleaning (or GTA822 for cleaning). Thinning is usually not required. For surface preparation, choice of equipment, application temperatures, drying times and overcoating intervals, always follow the current International Technical Data Sheet (TDS). COMPATIBILITY Intershield 300 is used as the primer in System A (together with Intergard 263 and Interspeed 6400 / Interswift 6800HS) or in System B (together with Intersleek 737 and Intersleek 1100SR). Where the highest level of resistance to mechanical damage is required (e.g. ice conditions, harbour operation, offshore structures), Intershield 300 is the first choice over Intergard 7500 or Intergard 7600. IMPORTANT Intershield 300 is a professional two-component epoxy coating. Part A and Part B form a single system and must be used in the specified mixing ratio of 2.5 : 1. Technical data may vary depending on colour, area of use, coating system and application conditions. Always check the current technical and safety data sheets before use.

€436.41

Contact

Not sure what to choose?

Our team will advise you, present the protection options, and together we will find the best solution for your vessel.

Call +386 (0)51 855 299 Send an inquiry

info@antifouling.si

Grab the helm and give it a spin

0
turns: 0
top speed (rpm)