SEAJET SEOSIL / TIE COAT FOR SILICONE

Name: SEAJET SEOSIL / TIE COAT FOR SILICONE
Brand: SEAJET
SKU: seajet-seosil-vezni-premaz-za-silikon
Price: 126.98 EUR

SEAJET Tie Coat – tie coat for the SEOSIL silicone system

€126.98

Select packaging below to see the exact price.

Colour

Available packaging

Select packaging …

Secure paymentFast delivery across Europe

Description

SEAJET Tie Coat – tie coat for the SEOSIL silicone system The essential intermediate layer that ensures silicone adhesion and determines the hull colour SEAJET Tie Coat is a one-component, fast-drying tie coat developed specifically for the SEAJET SEOSIL (Bioclean Eco) silicone foul-release system. Silicone does not adhere to the substrate or conventional coatings on its own, so Tie Coat acts as a bridge between the primer or old antifouling and the silicone, ensuring lasting adhesion and a long service life for the entire system. Since SEOSIL is transparent, Tie Coat determines the final hull colour. A major advantage is that it can be applied directly over existing, well-adhered antifouling – there is no need to remove the old coating. Advantages Ensures adhesion of the SEOSIL silicone coating Application over existing antifouling – no need to remove the old coating (if in good condition) Determines the hull colour – available in 4 colours One-component – no mixing and no pot life limit Fast drying – surface dry in just 40 minutes For all materials: GRP, wood, steel and aluminium (with the correct primer) Technical data Colours: white, black, dark blue (navy), red Pack sizes: 0.75 l / 2.5 l Coverage: approx. 15 m²/l per coat (theoretical, by roller) Film thickness: 100 µm wet / 30 µm dry per coat Application: brush, roller; spraying for professional use only Thinner: SEAJET Thinner A (15–25 %) Application temperature: air 5–35 °C, substrate at least 7 °C, humidity up to 85 % Shelf life: 2 years at 20 °C Drying times (at 20 °C) Surface dry: 40 minutes Fully dry: 4 hours Next coat of Tie Coat: after at least 4–5 hours (no maximum) Application of SEAJET SEOSIL: after at least 12 hours Coating system New GRP and steel: SEAJET 117 Multipurpose Epoxy Primer (silver) + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Wood: SEAJET 015 Underwater Primer + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Existing antifouling (in good condition): sand with P100 sandpaper + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Instructions for use 1. The surface must be clean, dry and free of grease, salt and fouling. Sand existing antifouling with P100 sandpaper, remove any flaking areas and remove dust. 2. Stir Tie Coat thoroughly before use and thin with SEAJET Thinner A (15–25 %). 3. Apply 2 coats at an interval of at least 4–5 hours. 4. After at least 12 hours, apply 2 coats of SEAJET SEOSIL. Tip Apply only to a dry, moisture-free substrate. Tie Coat is intended exclusively as a base for SEOSIL – on its own it does not protect against fouling. Safety labelling (GHS/CLP) Hazard pictograms are shown on the product page; read the label and safety data sheet before use.

Similar products

SEAJET 015 UNDERWATER PRIMER

SEAJET 015 Underwater Primer One-component primer and barrier coat for the underwater hull SEAJET 015 Underwater Primer is a fast-drying primer based on a special acrylic resin, designed for preparing the underwater hull before applying antifouling. It is used as a barrier coat over unknown or incompatible antifoulings and over Teflon (PTFE) antifoulings, to which new coatings otherwise adhere poorly. It forms a tough yet flexible protective film that stands up well to seawater. Advantages Barrier coat between incompatible coatings – the solution when you don't know which antifouling was applied before Suitable over Teflon (PTFE) antifoulings Excellent adhesion to existing antifouling and to subsequent coats Fast drying – touch dry in 15–40 minutes Seawater-resistant – for salt, brackish and fresh water Compatible with all SEAJET antifoulings One-component – no mixing with a hardener Application area Underwater hulls made of GRP (fibreglass), polyester, wood and steel. On aluminium, an epoxy primer must be applied first. Suitable for boats with speeds of up to 40 knots. Technical data Colour: silver grey Pack sizes: 0.75 l / 2.5 l / 5 l / 20 l Coverage: approx. 7.5 m²/l (theoretical) Dry film thickness: approx. 40 µm per coat Drying: touch dry in 15–40 min, fully dry in 1.5–4 h (depending on temperature and coat thickness) Application: brush, roller or airless spraying Thinner: SEAJET Thinner A Shelf life: at least 3 years at 20 °C Recommended number of coats GRP / polyester: 1 coat (as a barrier coat over existing antifouling) Wood and steel: 3–4 coats Aluminium: first an epoxy primer (e.g. SEAJET 117), then SEAJET 015 Directions for use The surface must be clean, dry and free of grease, wax, salt and fouling. The existing coating must be intact and well bonded to the substrate – remove any flaking areas, lightly sand the surface and remove the dust. Stir the paint thoroughly before use. Apply in even coats by brush or roller. Thin with SEAJET Thinner A if necessary. Allow each coat to dry before applying the next. Once dry, apply the SEAJET antifouling of your choice. Tip Do not apply at low temperatures, in high humidity or onto a damp substrate. Drying times are longer at lower temperatures and with thicker coats. For small touch-ups and hard-to-reach areas, SEAJET 015 is also available as a spray (400 ml).

from€19.70

SEAJET 015 SPRAY / UNDERWATER PRIMER

SEAJET 015 Underwater Primer – 400 ml spray Fast-drying primer and barrier coat for the underwater hull in a handy aerosol SEAJET 015 Underwater Primer is a one-component acrylic resin primer for preparing the underwater hull before applying a new antifouling. It acts as a barrier coat that separates the old and new coatings when you don't know which antifouling was applied before, or when the old and new coatings can't be combined. In spray form it is ideal for small touch-ups, hard-to-reach areas and quick spot repairs. Benefits Barrier coat between incompatible coatings – prevents reactions between old and new antifouling Also suitable over Teflon (PTFE) antifoulings, to which other coatings adhere poorly Excellent adhesion to existing, well-bonded coatings Fast drying – you can carry on working the same day Handy aerosol – no brushes, rollers or thinning; easily reaches awkward spots Compatible with all SEAJET antifoulings Areas of use Underwater hulls in GRP (fibreglass) and wood Small touch-ups and local antifouling renovation Hard-to-reach areas: around the skeg, rudder, propeller shaft, keel and through-hull fittings Technical data Contents: 400 ml aerosol Colour: silver Base: one-component acrylic resin Recommended number of coats: 3–4 Coverage: small areas; approx. 0.25 m² per can according to the seller Directions for use The surface must be clean, dry and free of grease, wax and salt. The existing coating must be undamaged and firmly bonded to the substrate. Sand it lightly and remove the dust. Shake the can vigorously for at least 2 minutes before use (until the ball rattles freely). Spray from a distance of approx. 20–30 cm in thin, even coats with overlapping passes. Apply 3–4 thin coats, allowing each one to become surface dry before applying the next. Once dry, apply the SEAJET antifouling of your choice. After use, turn the can upside down and spray until only gas comes out, so the nozzle doesn't clog. Tip Do not apply in direct sunlight, at low temperatures, in high humidity or onto a damp surface. For larger areas, the more economical choice is SEAJET 015 in a tin (0.75 l or 2.5 l), applied by brush, roller or spray gun. ⚠️ On bare aluminium, first apply an epoxy primer, e.g. SEAJET 117 Multi Purpose Epoxy Primer.

€23.20

SEAJET 012 UNIVERSAL PRIMER/UNDERCOAT

SEAJET 012 Universal Primer/Undercoat One-component universal primer for boats above the waterline SEAJET 012 is a fast-drying primer and undercoat for preparing surfaces before applying one-component topcoats. It adheres excellently to fibreglass (GRP), wood and steel, and on steel it also provides good corrosion protection. It is easy to use, making it an excellent choice both for professionals and for boat owners who do their own maintenance. Benefits Universal use – suitable for GRP, wood, steel and aluminium (with prior preparation) Fast drying – shorter time between coats and a faster finish Excellent adhesion – a solid base for a long-lasting topcoat Corrosion protection on steel surfaces One-component – no mixing with hardener, ready to use Areas of use Above the waterline only: topsides, decks, superstructures, boat interiors, metal and wooden fittings. Also suitable for renovating old, well-sanded coatings. Technical data Colour: off-white Pack sizes: 750 ml / 2.5 l Coverage: approx. 5.8 m² per 750 ml (approx. 7.7 m²/l) when applied by brush or roller Dry film thickness: approx. 30 µm per coat Application: brush, roller or airless spray Thinner: SEAJET Thinner U Recommended number of coats GRP and previously painted wood: 1 coat Aluminium: 2 coats (after proper preparation) Bare wood: 3–4 coats Steel: 2 coats over suitable corrosion protection Directions for use Thoroughly clean, degrease and sand the surface. Remove the dust. Stir the paint well before use. Apply in thin, even coats. Thin with SEAJET Thinner U if necessary. Before applying the next coat, wait for the previous one to dry and sand it lightly. As a topcoat, we recommend SEAJET Unythane Finish or another one-component topcoat. Tip Do not apply at low temperatures, in high humidity or onto a damp surface. For detailed application conditions and drying times, refer to the manufacturer's technical data sheet. ⚠️ Not suitable for the underwater hull – for that, choose SEAJET 015 Underwater Primer or SEAJET 117 Epoxy Primer.

from€18.86

SEAJET 117 SPRAY / MULTIPURPOSE EPOXY PRIMER

SEAJET 117 Multipurpose Epoxy Primer – 400 ml spray Epoxy primer in an aerosol can – ideal for spot repairs above and below the waterline SEAJET 117 spray is a handy version of the popular SEAJET 117 epoxy primer, intended for small and spot repairs – gelcoat damage, scratches down to the substrate, keel repairs, metal parts or drives. There are no components to mix, no tools to clean and no large can to open – you apply the primer straight from the aerosol. The primer offers high coverage and outstanding adhesion, forms a permanently waterproof film that is impermeable to water vapour, and is abrasion-resistant. Below the waterline it acts as a barrier against water ingress and a base for antifouling; above the waterline it is a base for two-component topcoats. Advantages Handy aerosol – no mixing, brushes or tool cleaning Ideal for spot repairs and hard-to-reach areas Above and below the waterline Outstanding adhesion to GRP, gelcoat, steel and aluminium Impermeable to water vapour – protects against water ingress Abrasion-resistant and long-lasting High coverage Area of use Spot repairs to the hull below and above the waterline, gelcoat damage, keels, metal parts, drive legs, brackets, fittings. Substrates: GRP, gelcoat, steel, aluminium. Technical data Contents: 400 ml aerosol Colour: silver grey Coverage: approx. 0.5 m² at 80 µm (2 coats) Film thickness: 30–40 µm per coat Recommended number of coats: 2 Cleaning: SEAJET Thinner E Directions for use The surface must be clean, dry and free of grease, wax and salt. Degrease and sand GRP and gelcoat; sand metals back to bright metal. Remove dust. Protect the area around the repair with masking tape and plastic sheeting. Shake the can vigorously for at least 2 minutes before use. Spray from a distance of approx. 20–30 cm in thin, even coats with overlapping passes. Apply 2 coats; wait until the first coat is touch dry before applying the second. Once dry, apply antifouling (below the waterline) or a topcoat (above the waterline). After use, turn the can upside down and spray until only propellant comes out, so the nozzle does not clog. Tip For larger areas and preventive osmosis protection, SEAJET 117 Multipurpose Epoxy Primer in cans (0.75 l – 20 l) is more economical. Use only outdoors or in a well-ventilated area. Hazard labelling (GHS/CLP) Pictograms: GHS02, GHS07 Signal word: DANGER H222 Extremely flammable aerosol. H229 Pressurised container: may burst if heated. H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H336 May cause drowsiness or dizziness. H412 Harmful to aquatic life with long lasting effects.

€34.04

Contact

Not sure what to choose?

Our team will advise you, present the protection options, and together we will find the best solution for your vessel.

Call +386 (0)51 855 299 Send an inquiry

info@antifouling.si

Grab the helm and give it a spin

0
turns: 0
top speed (rpm)