SEAJETBoat primers

SEAJET 114 PROPELLER PRIMER

Name: SEAJET 114 PROPELLER PRIMER
Brand: SEAJET
SKU: seajet-114-propeller-primer-mws
Price: 26.44 EUR

SEAJET 114 Propeller Primer – epoxy primer for propellers and drive parts

€26.44

Select packaging below to see the exact price.

Available packaging

Select packaging …

Secure paymentFast delivery across Europe

Hazard pictograms

Read the label and safety data sheet before use.

Description

SEAJET 114 Propeller Primer – epoxy primer for propellers and drive parts Maximum adhesion to aluminium, alloys and bronze – outperforms conventional etch primers SEAJET 114 Propeller Primer is a clear two-component epoxy primer developed specifically for propellers, drive legs, outboard motors, shafts and trim tabs. Ordinary coatings adhere poorly to these parts and soon flake off – because of the smooth metal surface, high revs and cavitation. SEAJET 114 provides outstanding adhesion to aluminium, aluminium alloys and bronze and performs better than conventional etch primers. It is the ideal base for SEAJET 034 EMPEROR A antifouling, together with which it forms a reliable protection system for drive parts. It can be used above and below the waterline. Advantages Maximum adhesion to aluminium, alloys and bronze Better than etch primers Clear – preserves the look of the metal Ideal base for SEAJET 034 EMPEROR A antifouling For salt and fresh water, above and below the waterline High coverage – a small pack is enough for a drive and propeller Area of use Propellers, drive legs (Z-drive, sail drive), outboard motors, propeller shafts, trim tabs and other metal parts made of aluminium, alloys and bronze. Technical data Colour: clear Pack size: 0.25 l (base + hardener) Mixing ratio: 60 : 40 (by volume) – base : hardener Coverage: approx. 10–15 m²/l Dry film thickness: 25–35 µm (1 thin coat) Directions for use 1. Preparation: remove all dirt, fouling and old coating from the parts. Sand bare metal with P80–P120 abrasive paper and factory-painted surfaces with P180. Remove dust and degrease. 2. Mix the base and hardener thoroughly in a 60 : 40 ratio. 3. Apply 1 thin, even coat. 4. After approx. 10 hours (at 20 °C), apply antifouling, e.g. 2 coats of SEAJET 034 EMPEROR A. Tip Before application, mask off anodes, seals and any parts you do not want coated. Never paint zinc anodes. For the complete system in one pack, the SEAJET Triple Pack (114 Propeller Primer + 034 EMPEROR A) is available. Hazard labelling (GHS/CLP) Pictograms: GHS02, GHS05, GHS07, GHS08, GHS09 Signal word: DANGER H225 Highly flammable liquid and vapour. H226 Flammable liquid and vapour. H302 Harmful if swallowed. H304 May be fatal if swallowed and enters airways. H314 Causes severe skin burns and eye damage. H315 Causes skin irritation. H317 May cause an allergic skin reaction. H318 Causes serious eye damage. H335 May cause respiratory irritation. H336 May cause drowsiness or dizziness. H341 Suspected of causing genetic defects. H361 Suspected of damaging fertility or the unborn child. H373 May cause damage to organs through prolonged or repeated exposure. H412 Harmful to aquatic life with long lasting effects. The labelling applies to both components together – see the label of each component for details.

Similar products

SEAJET 015 UNDERWATER PRIMER

SEAJET 015 Underwater Primer One-component primer and barrier coat for the underwater hull SEAJET 015 Underwater Primer is a fast-drying primer based on a special acrylic resin, designed for preparing the underwater hull before applying antifouling. It is used as a barrier coat over unknown or incompatible antifoulings and over Teflon (PTFE) antifoulings, to which new coatings otherwise adhere poorly. It forms a tough yet flexible protective film that stands up well to seawater. Advantages Barrier coat between incompatible coatings – the solution when you don't know which antifouling was applied before Suitable over Teflon (PTFE) antifoulings Excellent adhesion to existing antifouling and to subsequent coats Fast drying – touch dry in 15–40 minutes Seawater-resistant – for salt, brackish and fresh water Compatible with all SEAJET antifoulings One-component – no mixing with a hardener Application area Underwater hulls made of GRP (fibreglass), polyester, wood and steel. On aluminium, an epoxy primer must be applied first. Suitable for boats with speeds of up to 40 knots. Technical data Colour: silver grey Pack sizes: 0.75 l / 2.5 l / 5 l / 20 l Coverage: approx. 7.5 m²/l (theoretical) Dry film thickness: approx. 40 µm per coat Drying: touch dry in 15–40 min, fully dry in 1.5–4 h (depending on temperature and coat thickness) Application: brush, roller or airless spraying Thinner: SEAJET Thinner A Shelf life: at least 3 years at 20 °C Recommended number of coats GRP / polyester: 1 coat (as a barrier coat over existing antifouling) Wood and steel: 3–4 coats Aluminium: first an epoxy primer (e.g. SEAJET 117), then SEAJET 015 Directions for use The surface must be clean, dry and free of grease, wax, salt and fouling. The existing coating must be intact and well bonded to the substrate – remove any flaking areas, lightly sand the surface and remove the dust. Stir the paint thoroughly before use. Apply in even coats by brush or roller. Thin with SEAJET Thinner A if necessary. Allow each coat to dry before applying the next. Once dry, apply the SEAJET antifouling of your choice. Tip Do not apply at low temperatures, in high humidity or onto a damp substrate. Drying times are longer at lower temperatures and with thicker coats. For small touch-ups and hard-to-reach areas, SEAJET 015 is also available as a spray (400 ml).

from€19.70

SEAJET 015 SPRAY / UNDERWATER PRIMER

SEAJET 015 Underwater Primer – 400 ml spray Fast-drying primer and barrier coat for the underwater hull in a handy aerosol SEAJET 015 Underwater Primer is a one-component acrylic resin primer for preparing the underwater hull before applying a new antifouling. It acts as a barrier coat that separates the old and new coatings when you don't know which antifouling was applied before, or when the old and new coatings can't be combined. In spray form it is ideal for small touch-ups, hard-to-reach areas and quick spot repairs. Benefits Barrier coat between incompatible coatings – prevents reactions between old and new antifouling Also suitable over Teflon (PTFE) antifoulings, to which other coatings adhere poorly Excellent adhesion to existing, well-bonded coatings Fast drying – you can carry on working the same day Handy aerosol – no brushes, rollers or thinning; easily reaches awkward spots Compatible with all SEAJET antifoulings Areas of use Underwater hulls in GRP (fibreglass) and wood Small touch-ups and local antifouling renovation Hard-to-reach areas: around the skeg, rudder, propeller shaft, keel and through-hull fittings Technical data Contents: 400 ml aerosol Colour: silver Base: one-component acrylic resin Recommended number of coats: 3–4 Coverage: small areas; approx. 0.25 m² per can according to the seller Directions for use The surface must be clean, dry and free of grease, wax and salt. The existing coating must be undamaged and firmly bonded to the substrate. Sand it lightly and remove the dust. Shake the can vigorously for at least 2 minutes before use (until the ball rattles freely). Spray from a distance of approx. 20–30 cm in thin, even coats with overlapping passes. Apply 3–4 thin coats, allowing each one to become surface dry before applying the next. Once dry, apply the SEAJET antifouling of your choice. After use, turn the can upside down and spray until only gas comes out, so the nozzle doesn't clog. Tip Do not apply in direct sunlight, at low temperatures, in high humidity or onto a damp surface. For larger areas, the more economical choice is SEAJET 015 in a tin (0.75 l or 2.5 l), applied by brush, roller or spray gun. ⚠️ On bare aluminium, first apply an epoxy primer, e.g. SEAJET 117 Multi Purpose Epoxy Primer.

€23.20

SEAJET 012 UNIVERSAL PRIMER/UNDERCOAT

SEAJET 012 Universal Primer/Undercoat One-component universal primer for boats above the waterline SEAJET 012 is a fast-drying primer and undercoat for preparing surfaces before applying one-component topcoats. It adheres excellently to fibreglass (GRP), wood and steel, and on steel it also provides good corrosion protection. It is easy to use, making it an excellent choice both for professionals and for boat owners who do their own maintenance. Benefits Universal use – suitable for GRP, wood, steel and aluminium (with prior preparation) Fast drying – shorter time between coats and a faster finish Excellent adhesion – a solid base for a long-lasting topcoat Corrosion protection on steel surfaces One-component – no mixing with hardener, ready to use Areas of use Above the waterline only: topsides, decks, superstructures, boat interiors, metal and wooden fittings. Also suitable for renovating old, well-sanded coatings. Technical data Colour: off-white Pack sizes: 750 ml / 2.5 l Coverage: approx. 5.8 m² per 750 ml (approx. 7.7 m²/l) when applied by brush or roller Dry film thickness: approx. 30 µm per coat Application: brush, roller or airless spray Thinner: SEAJET Thinner U Recommended number of coats GRP and previously painted wood: 1 coat Aluminium: 2 coats (after proper preparation) Bare wood: 3–4 coats Steel: 2 coats over suitable corrosion protection Directions for use Thoroughly clean, degrease and sand the surface. Remove the dust. Stir the paint well before use. Apply in thin, even coats. Thin with SEAJET Thinner U if necessary. Before applying the next coat, wait for the previous one to dry and sand it lightly. As a topcoat, we recommend SEAJET Unythane Finish or another one-component topcoat. Tip Do not apply at low temperatures, in high humidity or onto a damp surface. For detailed application conditions and drying times, refer to the manufacturer's technical data sheet. ⚠️ Not suitable for the underwater hull – for that, choose SEAJET 015 Underwater Primer or SEAJET 117 Epoxy Primer.

from€18.86

SEAJET SEOSIL / TIE COAT FOR SILICONE

SEAJET Tie Coat – tie coat for the SEOSIL silicone system The essential intermediate layer that ensures silicone adhesion and determines the hull colour SEAJET Tie Coat is a one-component, fast-drying tie coat developed specifically for the SEAJET SEOSIL (Bioclean Eco) silicone foul-release system. Silicone does not adhere to the substrate or conventional coatings on its own, so Tie Coat acts as a bridge between the primer or old antifouling and the silicone, ensuring lasting adhesion and a long service life for the entire system. Since SEOSIL is transparent, Tie Coat determines the final hull colour. A major advantage is that it can be applied directly over existing, well-adhered antifouling – there is no need to remove the old coating. Advantages Ensures adhesion of the SEOSIL silicone coating Application over existing antifouling – no need to remove the old coating (if in good condition) Determines the hull colour – available in 4 colours One-component – no mixing and no pot life limit Fast drying – surface dry in just 40 minutes For all materials: GRP, wood, steel and aluminium (with the correct primer) Technical data Colours: white, black, dark blue (navy), red Pack sizes: 0.75 l / 2.5 l Coverage: approx. 15 m²/l per coat (theoretical, by roller) Film thickness: 100 µm wet / 30 µm dry per coat Application: brush, roller; spraying for professional use only Thinner: SEAJET Thinner A (15–25 %) Application temperature: air 5–35 °C, substrate at least 7 °C, humidity up to 85 % Shelf life: 2 years at 20 °C Drying times (at 20 °C) Surface dry: 40 minutes Fully dry: 4 hours Next coat of Tie Coat: after at least 4–5 hours (no maximum) Application of SEAJET SEOSIL: after at least 12 hours Coating system New GRP and steel: SEAJET 117 Multipurpose Epoxy Primer (silver) + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Wood: SEAJET 015 Underwater Primer + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Existing antifouling (in good condition): sand with P100 sandpaper + 2 coats of SEAJET Tie Coat + 2 coats of SEAJET SEOSIL Instructions for use The surface must be clean, dry and free of grease, salt and fouling. Sand existing antifouling with P100 sandpaper, remove any flaking areas and remove dust. Stir Tie Coat thoroughly before use and thin with SEAJET Thinner A (15–25 %). Apply 2 coats at an interval of at least 4–5 hours. After at least 12 hours, apply 2 coats of SEAJET SEOSIL. Tip Apply only to a dry, moisture-free substrate. Tie Coat is intended exclusively as a base for SEOSIL – on its own it does not protect against fouling. Safety labelling (GHS/CLP) Hazard pictograms are shown on the product page; read the label and safety data sheet before use.

€126.98

Contact

Not sure what to choose?

Our team will advise you, present the protection options, and together we will find the best solution for your vessel.

Call +386 (0)51 855 299 Send an inquiry

info@antifouling.si

Grab the helm and give it a spin

0
turns: 0
top speed (rpm)